![seadoo vts guages seadoo vts guages](https://jetskipartsguy.com/wp-content/uploads/2015/12/1995SeadooXPVTSTachometerFuelGaugeAssy_278000451278000502278000590.jpg)
- Seadoo vts guages how to#
- Seadoo vts guages install#
- Seadoo vts guages full#
- Seadoo vts guages professional#
![seadoo vts guages seadoo vts guages](https://assets.suredone.com/684295/media-photos/sd5504-sea-doo-bombardier-1997-1998-xp-tachometer-speedo-vts-gauge-kit-278001104-2.jpeg)
its actually pretty easy and it comes off in big chunks once you have it heated up to higher temperature. Scrape the upper layer of epoxy to expose the PCB
![seadoo vts guages seadoo vts guages](https://seadooonboard.files.wordpress.com/2013/06/smaller-for-blog-2013-sea-doo-gti-limited-155-vts-eco.jpg)
Seadoo vts guages how to#
Its quite easy if you have basic electronics knowledge and know how to solder.ġ. So i decided to give it a go since i had nothing to loose. TrimFix only gives you 4 positions for the gauge, and its over $150 shipped (im from Canada)īut i haven't seen anything about actually fixing the original module. Well there is lots of information about the TrimFix module and/or cheap relay bypass fix. Nozzle would 'unscrew' in the lowest position and would not come back up without physical help. Unfortunately this disabled the gauge and limit stops were not active. Previous owner ended up cutting all the wires off the module and wiring his cheap relay fix.
Seadoo vts guages full#
No special tools needed, full illustrated instructions are included.So i picked up my first seadoo, turned out vts was busted. Installation is easy and takes an average of 30-45 minutes to install. Again eliminating the need to replace, or even remove the VTS housing
Seadoo vts guages install#
The electronic control module and gauge position sensor mount and install externally from the VTS housing and connect right to the existing wiring, the gauge position sensor attaches on the outside of the VTS Housing connecting to the original wiring. How the TrimFix System solves all of this is simple, by replacing the VTS Housing's internal control module, gauge position sensor and electronics with external components. Has warranty with free replacement for as long as you own your ski Travel stops at max up and down positions The TrimFix works with your existing switch and gauge The Trimfix System eliminates all of this, without replacing, or even removing the VTS Housing at all ! Then, after that is all done, it won't be long and it will be time to do it all again when the VTS housing fails again, which it is sure to do.
Seadoo vts guages professional#
Replacing the VTS housing is repair that should be performed by a professional technician. As many know, replacing the VTS housing is quite involved, requiring skill to be done correctly, special tools are needed, the repair is time consuming, and if it not done correctly, a leak into the hull and the craft will take on water introducing a variety of damages which could have been avoided. The electronic components that operate the gauge to indicate trim position are also located inside the VTS Housing as well and are also non-serviceable, again leaving no option but to replace the complete housing to repair the problem. The electronics inside the housing are encapsulated and non-serviceable, making replacement of the complete VTS Housing as the only option for repair. The common cause of failure is due to the control module, gauge position sensor, and electronics being located internally within the VTS Housing and seems that no matter what is done, they take on moisture due to their design and location. Only to be replaced again not long after because it will fail as they always do. The only repair option was to replace the complete VTS Housing. Until now, fixing trim operation on Seadoo personal watercraft was a frequent and expensive repair. Having to replace them every season gets costly. This is the SOLUTION to the constant failing and expensive VTS Housings.Ī new VTS housing costs over $300 and will surely fail again as they always do. VTS Housing failure is extremely common and replacement of the entire VTS Housing was required to fix this problem, The Trim FIX module fixes trim operation without the need to replace, or even remove, a failed VTS housing. Introducing the Trim-FIX module for SeaDoo personal watercraft.